The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.

2003 -2004.5 Dodge 5.9L Cummins Reman Injector (305HP) w/ New Component

2003 -2004.5 Dodge 5.9L Cummins Reman Injector (305HP) w/ New Component

$215.00
SKU:
D59INJ305R
Condition:
Refurbished
Weight:
2.00 LBS
Core:
$100.00

2003 -2004.5 DODGE 5.9L CUMMINS DIESEL REMAN INJECTOR (305HP) WITH NEW BOSCH NOZZLE NEW O-RINGS & COPPER CRUSH WASHERS

 

REMAN CUMMINS 5.9L DIESEL FUEL INJECTOR USING BRAND NEW COMPONENTS.COMPLETE REPLACEMENT OF NEW BOSCH NOZZLE AND CONTROL VALVE ASSEMBLY EACH INJECTOR INCLUDES ALL NEW O-RINGS & COPPER CRUSH WASHERS.

 

Injector Type: Bosch common-rail injectors
Flow Rate: Approximately 25 liters per hour (lph) at 160 MPa (megapascal)
Fuel Pressure: Up to 23,000 psi (1,600 bar)
Actuation Method: Solenoid
Control Method: Electronic signals from the Engine Control Module (ECM)

 

Does your Dodge Ram have over 80k and have a hard start? Maybe it doesn't start at all? Maybe it misses or makes a funny ticking sound? These injectors may be what you need.

Dodge puts 10 micron fuel filters in the Cummins motor of you truck. Your injectors need a 2 micron filter to keep all of the gunk in your fuel out of them. Many people do not even get to 50k miles before they have a problem caused by fuel contamination.

Another common problem for these injectors are cracks caused by a rail pressure box. If you are using an aftermarket power enhancement and it plugs into the rail pressure, chances are its a pressure box. There are very few rail pressure boxes that are a small enough amount of pressure to be safe, so use them at your own risk. Even some downloaders have the ability to raise pressure

 

OEM NUMBERS / CROSS REFERENCES: 

0986435503, 0445120210,0445120113, 0445120018, 0445120255, 4940589NX, R8004082AA, DT590001R, 3949913, 4940589, 3949619, 3947550, 5254686, 5263318, R5086894, R80040821

Mopar Part # - 5086874AB, 5175565AA, 6800533AA

Cummins - 3979419, 4929865

Bosch Part# - F 00R J01 572, F 00R C00 647, F 00R J01 831

 

Install Specs:

Injector: Pre-torque hold-down bolt to 44 inch-pounds to ensure injector is seated & centered.

Feed tube: Pre-torque to 11 ft.-lbs. to ensure feed tube is seated & centered.

Injector hold-down bolts final install: 89 inch-lbs.

Feed tube final install: 34 ft.-lbs.

Rocker Arm mounting bolts: 27 ft.-lbs.

Wire connector nuts final install: 13 inch-pounds. DO NOT OVER TORQUE!

Feed tube lines: Torque at 22 ft.-lbs.

 

**Don't forget to pick up your set of Dodge 5.9L Cummins Feed Tubes along with these injectors - Bosch recommends replacing feed tube when replacing all injectors for the best fuel economy and performance - SKU D59TUBE**

 

**⚠California Proposition 65 Warning: Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.

Visit: www.p65warnings.ca.gov